Details for version 7.5

For full details of these enhancements and others not listed here please refer to the Release Notes manual.

x86 32bit and 64bit versions

A 32bit version of Zencrack has been available for x86 processors running Windows since 1998. The release of version 7.4a of Zencrack in July 2006 saw the first use of the Intel Fortran compiler for Zencrack. This has been extended in the 7.5 release to provide 64bit versions of Zencrack for x86 processors running 64bit versions of Windows or Linux. Extensive testing has taken place using Windows XP Professional x64 and SuSe Linux Enterprise Desktop 10. A reduced set of testing has been carried out using Red Hat Enterprise Linux WS Release 4.

The 32bit Windows release continues to be supplied in Compaq Fortran and Intel Fortran variants.

General

• A new "enhanced ring control" mapping option for crack-blocks has been introduced. This method attempts to keep the crack front element rings as close as possible to circular. The enhanced method is particularly suited to cases where the target element is distorted. In previous releases extreme distortion of the target elements may have meant that results were unacceptable. The new mapping method allows analysis to be completed reliably where it would previously not have been possible.




• The enhanced ring control method also produces better meshes as the crack moves away from the ideal size within the crack-block.




• Two new methods are available for cases when a complex load cycle is modelled by analysing multiple increments through the cycle. In such cases it may not be possible in advance to specify which load increments produce the minimum and maximum energy release rates. Indeed, the critical load increment may be different from one crack front node to the next. An option is now available to search through all result sets for minimum and maximum energy release rate conditions for each crack front node. In this type of search scenario the loading is likely to be non-proportional through the load cycle i.e. the energy release rate magnitude and direction are changing through the cycle. The search method identifies the range for crack growth calculations, but not the direction. An option of taking a weighted average direction across all result sets is available.
• An "automatic split" option is introduced to allow cracks to be generated in some configurations that were previously difficult to work with. This option, aimed at through crack geometries, allows edges that cannot be split using the face-based *SPLIT option to be separated without any user input. Two examples where this situation may arise are shown below.





• Increased flexibility is available on the SAVE keyword for specifying the save parameters for different file types. This allows, for example, the main f.e. results file to be saved every 5th step but the cracked mesh input file to be saved every step. This can have significant benefits on disk space usage for large models in a crack growth analysis.
• The control and generation of crack related node and elements has been standardised across the Abaqus, Ansys and Marc interfaces. Options are added to turn on or off the various types of sets that can be created. In addition, some new sets are available. These changes enhance the possibilities available while post-processing the cracked mesh.
• New element sets are available that combine all crack-blocks on each side of the crack front. This means that side 1 or side 2 of the crack can be selected via single sets.
• The sets for split elements that existed in v7.4a are divided into separate sets for each side of the crack face.
• A new element set option is added to allow creation of element sets on the outer faces of all crack-blocks.

Crack-block library

• The crack-block st12x1 that was released with Zencrack 7.4a is now moved into a new "family" and becomes s05_t12x1. A new corner crack-block s05_q24x2 is included as the other member of this crack-block family.

• Two new large crack-block families are available with this release. They are families l05 and l06. The crack-blocks in family l06 (shown below) are 2x2x2 refinements of crack-blocks in family l05. These new crack-blocks are intended to take full advantage of the new mapping options available via the enhanced ring control methodology. Family l05 also contains three extra crack-blocks that have additional sub-divisions along the crack front.

Abaqus interface

• Shear load types TRSHRn and TRSHRnNU are updated on the outer surfaces of the crack-blocks if these loads are applied to the target crack-block elements.

Ansys interface

• The Ansys interface is upgraded to allow use of the j-integral capability that is now available in Ansys. Although introduced in Ansys 11.0, the calculation and processing of j-integrals by Zencrack requires Ansys 11.0SP1 (or later). The addition of this capability allows users to choose whether a crack growth analysis is based on results derived from j-integral evaluation or from stress intensity factors derived from nodal displacements. This choice is made on the ENERGY RELEASE RATE keyword. All generation and processing of j-integral data is handled fully automatically and allows for non-planar crack development.
• The handling of multiple sets of load increments from an Ansys (non-linear) analysis has been improved.
• The handling of thermal-stress analysis in the Ansys interface has been improved.

Finas interface

• Support is added for Finas user subroutines.

Marc interface

• An improved method is introduced to allow large crack-blocks to be used with the Marc interface. The method is based on the automatic creation of element sets for the outer face of each crack-block by Zencrack in conjunction with glued contact in Marc.

• Processing of multiple load increments from the f.e. analysis is now possible. This means that the full scope of the Zencrack load system methodology is available.
• The location of the Marc executable can be defined in the runzcr75 script file that is used to run Zencrack. The *EXE option still exists to allow the global setting to be overridden for individual jobs. Direct specification of Marc user subroutines via the Zencrack input file is also available. An option is included for whether or not to save the generated Marc executable.